The influence of the dimensions of the surface hardening region on the stress-strain state of a beam with a notch of~a~semicircular profile

V. P. Radchenko ; D. M. Shishkin

Journal of Samara State Technical University, Ser. Physical and Mathematical Sciences, Tome 24 (2020) no. 4, pp. 663-676.

Résumé

The influence of a size of the surface-plastic hardening region on the stress-strain state of a beam with a notch of a semicircular profile is investigated. The problem is reduced to a boundary value problem of fictitious thermoelasticity with the initial (plastic) deformations modeled by temperature anisrotropic deformations in an inhomogeneous temperature field. The solution is based on the finite element method. For model calculations, experimental data on the distribution of residual stresses in a smooth beam made of EP742 alloy after ultrasonic mechanical hardening were used as initial information. A variative numerical analysis of the effect of the notch radius and the size of the hardening zone of the beam face on the distribution of the components of the residual stress tensor in the smallest section from the bottom of the concentrator is carried out. It is shown that when the hardening zone is more than 16–20 % of the entire face area, the stress-strain state in the smallest section is practically stabilized. It was established that if the radius of the semicircular notch is less than the thickness of the hardened layer (the material compression area), an increase (in modulus) of the normal longitudinal component of the residual stress tensor occurs, and if the radius of the notch is greater than the thickness of the hardened layer, then a decrease (in modulus) of this value is observed in comparison with a similar component for a smooth reinforced beam for all values of the hardening zone more than 16–20 % of the entire face area of the beam. An experimental verification of the developed numerical method based on the finite element method for a beam with a fully hardened face is performed.

Détail

Keywords: advanced surface plastic hardening, area of hardening, semicircular notch, beam, EP742 alloy, residual stresses.

Bibliographie

[1] Birger I. A., Ostatochnye napriazheniia [Residual Stresses], Mashgiz, Moscow, 1963, 232 pp. (In Russian)

[2] Grinchenko I. G., Uprochnenie detalei iz zharoprochnykh i titanovykh splavov [Hardening Parts Made of High-Resistant and Titanium Alloys], Mashinostroenie, Moscow, 1971, 120 pp. (In Russian)

[3] Sulima A. M., Shuvalov V. A., Yagodkin Yu. D., Poverkhnostnyi sloi i ekspluatatsionnye svoistva detalei mashin [Surface Layer and Performance of Machine Parts], Mashinostroenie, Moscow, 1988, 240 pp. (In Russian)

[4] Kudryavtsev I. V., Poverkhnostnyi naklep dlia povysheniia prochnosti i dolgovechnosti detalei mashin poverkhnostnym plasticheskim deformirovaniem [Surface Strain Hardening to Increase the Strength and Durability of Machine Parts], Mashinostroenie, Moscow, 1969, 100 pp. (In Russian)

[5] Nozhnitskii Yu. A., Fishgoit A. V., Tkachenko R. I., Teplova S. V., “Development and application of new GTE parts hardening methods based on the plastic deformation of the surface layers”, Vestn. Dvigatel., 2006, no. 2, 8–16 (In Russian)

[6] Brockman R. A., Braisted W. R., Olson S. E., et. al., “Prediction and characterization of residual stresses from laser shock peening”, Intern. J. Fatigue, 36:1 (2012), 96–108 | DOI

[7] Dai K., Shaw L., “Analysis of fatigue resistance improvements via surface severe plastic deformation”, Intern. J. Fatigue, 30:8 (2008), 1398–1408 | DOI

[8] James M. N., Hughes D. J., Chen Z., et. al., “Residual stresses and fatigue performance”, Eng. Fail. Analysis, 14:2 (2007), 384–395 | DOI

[9] Majzoobi G. H., Azadikhah K., Nemati J., “The effects of deep rolling and shot peening on fretting fatigue resistance of Aluminum-7075-T6”, Mater. Sci. Eng. A, 516:1–2 (2009), 235–247 | DOI

[10] Soady K. A., “Life assessment methodologies incoroporating shot peening process effects: mechanistic consideration of residual stresses and strain hardening. Part 1 – Effect of shot peening on fatigue resistance”, Mater. Sci. Technol., 29:6 (2013), 673–651 | DOI

[11] Terres M. A., Laalai N., Sidhom H., “Effect of nitriding and shot-peening on the fatigue behavior of 42CrMo4 steel: Experimental analysis and predictive approach”, Mater. Design, 35 (2012), 741–748 | DOI

[12] Pavlov V. F., Kirpichev V. A., Vakulyuk V. S., Prognozirovanie soprotivleniia ustalosti poverkhnostno uprochnennykh detalei po ostatochnym napriazheniiam [Prediction of Fatigue Resistance of Surface Reinforced Parts by Residual Stresses], Samara Sci. Center of RAS, Samara, 2012, 125 pp. (In Russian)

[13] Saushkin M. N., Kurov A. Yu., “Analysis of stress state in semicircular profile notches after preliminary surface plastic deformation of solid cylindrical specimens”, Vestn. Samar. Gos. Tekhn. Univ., Ser. Fiz.-Mat. Nauki [J. Samara State Tech. Univ., Ser. Phys. Math. Sci.], 2012, no. 1(26), 133–140 (In Russian) | DOI | Zbl

[14] Radchenko V. P., Kurov A. Yu., “Effect of anisotropy of surface plastic hardening on formation of residual stresses in cylindrical samples with semicircular notch”, Vestn. Samar. Gos. Tekhn. Univ., Ser. Fiz.-Mat. Nauki [J. Samara State Tech. Univ., Ser. Phys. Math. Sci.], 20:4 (2016), 675–690 (In Russian) | DOI | Zbl

[15] Sazanov V. P., “Analysis of the mechanism of fatigue crack arrest in a cylindrical notched specimen”, Vestnik of Samara University. Aerospace and Mechanical Engineering, 17:1 (2018), 160–169 (In Russian) | DOI

[16] Doremus L., Cormier J., Villechaise P., et. al., “Influence of residual stresses on the fatigue crack growth from surface anomalies in a nickel-based superalloy”, Mater. Sci. Eng. A, 644 (2015), 234–246 | DOI

[17] Fleury R. M. N.., Nowell D., “Evaluating the influence of residual stresses and surface damage on fatigue life of nickel superalloys”, Intern. J. Fatigue, 105 (2017), 27–33 | DOI

[18] Pavlov V. F., Bukatyi A. S., Semyonova O. Yu., “Forecasting of the endurance limit of surface-hardened parts with stress concentrators”, Russian Engineering Research, 2019, no. 1, 3–7 (In Russian)

[19] Ivanov S. I., Shatunov M. P., Pavlov V. F., “Influence of residual stresses on notched specimen endurance”, Problems of Strength of Aircraft Structure Elements, v. 3, Kuibyshev Aviation Inst., Kuibyshev, 1974, 88–95 (In Russian)

[20] Pavlov V. F., Stolyarov A. K., Vakulyuk V. S., Kirpichev V. A., Raschet ostatochnykh napriazhenii v detaliakh s kontsentratorami napriazhenii po pervonachal'nym deformatsiiam [Calculation of Residual Stresses in Parts with Stress Concentrators by Initial Deformations], Samara Sci. Center of RAS, Samara, 2008, 124 pp. (In Russian)

[21] Vakulyuk V. S., Pavlov V. F., Sazanov V. P., Semyonova O. Yu., “The evaluation of the surface hardening influence on the endurance limit of parts under stress concentration conditions”, Proceedings of the Tenth Russian Conference on Solid Mechanics (September, 18–22, 2017, Samara, Russian Federation), v. 1, Samara State Technical Univ., Samara, 2017, 103–106 (In Russian)

[22] Pavlov V. F., Pis'marov A. V., Sazanov V. P., Surgutanov N. A., “Investigation of the dependence of the stress intensity factor on the crack depth in the notched details”, Proceedings of the Tenth Russian Conference on Solid Mechanics (September, 18–22, 2017, Samara, Russian Federation), v. 2, Samara State Technical Univ., Samara, 2017, 132–135 (In Russian)

[23] Radchenko V. P., Saushkin M. N., Bochkova T. I., “Mathematical modeling and experimental study of forming and relaxation of the residual stresses in plane samples made of EP742 alloy after the ultrasonic hardening under the hightemperature creep conditions”, PNRPU Mechanics Bulletin, 2016, no. 1, 93–112 (In Russian) | DOI

[24] Radchenko V. P., Shishkin D. M., “The method of reconstruction of residual stresses in a prismatic specimen with a notch of a semicircular profile after advanced surface plastic deformation”, Izv. Saratov Univ. (N. S.), Ser. Math. Mech. Inform, 20:4 (2020), 478–492 (In Russian) | DOI

[25] Vakuljuk V. S., “Investigation of influence of thickness hardened layer on the residual stresses in basin concentrator using initial strain”, Vestn. Samar. Gos. Tekhn. Univ., Ser. Fiz.-Mat. Nauki [J. Samara State Tech. Univ., Ser. Phys. Math. Sci.], 2010, no. 1(20), 222–225 (In Russian) | DOI

[26] Sazanov V. P., Kirpichev V. A., Vakulyuk V. S., Pavlov V. F., “The definition of initial deformations in the cylindrical parts surface layer by Finite Elements Modeling method using PATRAN/NASTRAN program complex”, Vestn. Ufimsk. Gos. Aviats. Techn. Univ., 19:2 (2015), 35–40 (In Russian)

[27] Radchenko V. P., Afanaseva O. S., Glebov V. E., “The effect of surface plastic hardening technology, residual stresses and boundary conditions on the buckling of a beam”, PNRPU Mechanics Bulletin, 2020, no. 1, 87–98 (In Russian) | DOI