Residual stresses relaxation in surface-hardened half-space under creep conditions

V. P. Radchenko ; T. I. Bochkova ; V. V. Tsvetkov

Journal of Samara State Technical University, Ser. Physical and Mathematical Sciences, Tome 19 (2015) no. 3, pp. 504-522.

Résumé

We developed the method for solving the problem of residual stresses relaxation in surface-hardened layer of half-space under creep conditions. At the first stage we made the reconstruction of stress-strain state in half-space after plastic surface hardening procedure based on partial information about distribution for one residual stress tensor component experimentally detected. At the second stage using a numerical method we solve the problem of relaxation of self-balanced residual stresses under creep conditions. To solve this problem we introduce the following Cartesian system: $x0y$ plane is aligned with hardened surface of half-space and $0z$ axis is directed to the depth of hardened layer. We also introduce the hypotheses of plane sections parallel to $x0z$ and $y0z$ planes. Detailed analysis of the problem has been done. Comparison of the calculated data with the corresponding test data was made for plane specimens (rectangular parallelepipeds) made of EP742 alloy during $T=650^\circ$ C after the ultrasonic hardening with four hardening modes. We use half-space to model these specimens because penetration's depth of residual stresses is less than specimen general size in two digit exponent. There is enough correspondence of experimental and calculated data. It is shown that there is a decay (in modulus) of pressing residual stresses under creep in 1.4–1.6 times.

Détail

Keywords: half-space, plastic surface hardening, residual stresses, creep, stresses relaxation.

Bibliographie

[1] Birger I. A., Ostatochnye napriazheniia [Residual stresses], Mashgiz, Moscow, 1963, 262 pp. (In Russian)

[2] Pavlov V. F., Kirpichev V. A., Ivanov V. B., Ostatochnye napriazheniia i soprotivlenie ustalosti uprochnennykh detalei s kontsentratorami napriazhenii [Residual Stresses and Fatigue Resistance of Hardened Parts with Stress Concentrators], Samara Research Center, Russian Academy of Sciences, Samara, 2008, 64 pp. (In Russian)

[3] Ivanov S. I., Pavlov V. F., Minin B. V., Kirpichev V. A., Kocherov E. P., Golovkin V. V., Ostatochnye napriazheniia i soprotivlenie ustalosti vysokonagruzhennykh rez'bovykh detalei [Residual Stresses and Fatigue Resistance of High-loaded Threaded Parts], Samara Research Center, Russian Academy of Sciences, Samara, 2015, 170 pp. (In Russian)

[4] I. G. Grichenko, Uprochnenie detaley iz zharoprochnykh i titanovykh splavov [Hardening components of heat-resistant and titanium alloys], Mashinostroenie, Moscow, 1971, 120 pp. (In Russian)

[5] B. A. Kravchenko, V. G. Krutsilo, G. N. Gutman, Termoplasticheskoe uprochnenie — rezerv povysheniya prochnosti i nadezhnosti detaley mashin [Thermoplastic hardening as a reserve increase of strength and reliability of machine parts], Samara State Technical Univ., Samara, 2000, 216 pp. (In Russian)

[6] Sulima A. M., Shuvalov V. A., Yagodkin Yu. D., Poverkhnostnyi sloi i ekspluatatsionnye svoistva detalei mashin [Surface layer and performance of machine parts], Mashinostroenie, Moscow, 1988, 240 pp. (In Russian)

[7] Radchenko V. P., Saushkin M. N., Polzuchest' i relaksatsiya ostatochnykh napryazheniy v uprochnonnykh konstruktsiyakh [Creep and relaxation of residual stresses in hardened structures], Mashinostroenie-1, Moscow, 2005, 226 pp. (In Russian)

[8] Altenberger, I., Nalla, R. K., Sano, Y., Wagner, L., Ritchie, R. O., “On the effect of deep-rolling and laser-peening on the stress-controlled low- and high-cycle fatigue behavior of Ti-6-Al-4V at elevated temperatures up to $550^\circ$ C”, Int. J. Fatigue, 44 (2012), 292–302 | DOI

[9] Brockman, R. A., Braisted W. R., Olson S. E., Tenaglia R. D., Clauer A. H., Langer K., Shepard M. J., “Prediction and characterization of residual stresses from laser shock peening”, Int. J. Fatigue, 36:1 (2012), 96–108 | DOI

[10] Dai K., Shaw L., “Analysis of fatigue resistance improvements via surface severe plastic deformation”, Int. J. Fatigue, 30:8 (2008), 1398–1408 | DOI

[11] James M. N., Hughes D. J., Chen Z., Lombard H., Hattingh D. G., Asquith D., Yates J. R., Webster P. J., “Residual stresses and fatigue performance”, Engineering Failfure Analysis, 14:2 (2007), 384–395 | DOI

[12] Majzoobi G.H., Azadikhah K., Nemati J., “The effects of deep rolling and shot peening on fretting fatigue resistance of Aluminum-7075-T6”, Materials Science and Engineering A, 516:1-2 (2009), 235–247 | DOI

[13] Soady K. A., “Life assessment methodologies incoroporating shot peening process effects: mechanistic consideration of residual stresses and strain hardening Part 1 – effect of shot peening on fatigue resistance”, Materials Science and Technology (United Kingdom), 29:6 (2013), 637–651 | DOI

[14] Terres M. A., Laalai N., Sidhom H., “Effect of nitriding and shot-peening on the fatigue behavior of 42CrMo4 steel: Experimental analysis and predictive approach”, Materials and Design, 35 (2012), 741–748 | DOI

[15] Radchenko V. P., Saushkin M. N., “Mathematical models of recovery and relaxation of residual stresses in the surface-hardened of cylindrical structural elements under creeping”, Izv. Vyssh. Uchebn. Zaved., Mashinostr., 2004, no. 11, 3–17 (In Russian)

[16] Radchenko V. P., Saushkin M. N., “Direct method of solving the boundary-value problem of relaxation of residual stresses in a hardened cylindrical specimen under creep conditions”, J. Appl. Mech. Tech. Phys., 50:6 (2009), 989–997 | DOI | MR | Zbl

[17] Radchenko V. P., Kocherov E. P., Saushkin M. N., Smyslov V. A., “Experimental and theoretical studies of the influence of a tensile load on the relaxation of residual stresses in a hardened cylindrical specimen under creep conditions”, J. Appl. Mech. Tech. Phys., 56:2 (2015), 169–177 | DOI | DOI

[18] Radchenko V. P., Tsvetkov V. V., “Kinetics of the stress-strain state of surface hardened cylindrical specimen under complex stress state of creep”, Vestn. Samar. Gos. Tekhn. Univ. Ser. Fiz.-Mat. Nauki [J. Samara State Tech. Univ., Ser. Phys. Math. Sci.], 2014, no. 1(32), 93–108 (In Russian) | DOI | Zbl

[19] Kolotnikova O. V., “Effectiveness of hardening by methods of plastic surface deformation of components operating at high temperatures”, Strength of Material, 15:2 (1983), 292–295 | DOI

[20] Radchenko V. P., Kirpichev V. A., Lunin V. A., “Influence of thermoexposition on residual stresses of specimens from EP742 alloy after the ultrasonic hardening”, Vestn. Samar. Gos. Tekhn. Univ. Ser. Tech. Nauki, 2012, no. 3(35), 147–154 (In Russian) | MR

[21] Saushkin M. N., Afanas'eva O. S., “Investigation of residual stresses relaxation in the surface hardened disk hole of a gas-turbine engine”, Vestn. Samar. Gos. Tekhn. Univ. Ser. Fiz.-Mat. Nauki [J. Samara State Tech. Univ., Ser. Phys. Math. Sci.], 2007, no. 2(15), 51–59 (In Russian) | DOI

[22] Saushkin M. N., Afanas'eva O. S., Prosvirkina E. A., “Assessment of residual stresses relaxation in a hardened rotating blade under creep conditions”, Vestn. Samar. Gos. Tekhn. Univ. Ser. Fiz.-Mat. Nauki [J. Samara State Tech. Univ., Ser. Phys. Math. Sci.], 2007, no. 1(14), 62–70 (In Russian) | DOI

[23] Kirpichev V. A., Saushkin M. N., Afanas'eva O. S., Smyslov V. A., “Predictions of fatigue endurance limit of hardening samples at elevated temperature”, Vestn. Samar. Gos. Tekhn. Univ. Ser. Fiz.-Mat. Nauki [J. Samara State Tech. Univ., Ser. Phys. Math. Sci.], 2010, no. 1(20), 218–221 (In Russian) | DOI

[24] Radchenko V. P., Saushkin M. N., Pavlov V. F., “Method of calculating the fields of residual stresses and plastic strains in cylindrical specimens with allowance for surface hardening anisotropy”, J. Appl. Mech. Tech. Phys., 52:2 (2011), 303–310 | DOI | Zbl

[25] Radchenko V. P., Pavlov V. F., Saushkin M. N., “Investigation of surface plastic hardening anisotropy influence on residual stresses distribution in hollow and solid cylindrical specimens”, PNRPU Mechanics Bulletin, 2015, no. 1, 130–147 (In Russian) | DOI | MR

[26] Ivanov S. I., Bukatyi S. A., “On form distortion of the details like a beam after plastic surface deformation”, Izv. vuzov. Aviatsionnaia tekhnika, 1976, no. 3, 127–129 (In Russian)

[27] Ivanov S. I., “Residual stresses determination in plates by the method of strips”, Voprosy prochnosti elementov aviatsionnykh konstruktsii [Problems of strength for aircraft structural elements], v. 48, Kuibyshev Aviation Institute, Kuibyshev, 1971, 139–152 (In Russian)

[28] Zoteev V. E., Parametricheskaia identifikatsiia dissipativnykh mekhanicheskikh sistem na osnove raznostnykh uravnenii [Parametric identification of dissipative mechanical systems based on difference equations], Mashinostroenie, Moscow, 2009, 344 pp.

[29] Zoteev V. E., Svistunova A. A., “A numerical method for determining the parameters of the stress state of the surface hardened layer of cylindrical element on the basis of experimental data”, Perspektivnye informatsionnye tekhnologii (PIT 2015) [Advanced information technologies (PIT 2015)], Proceedings of the Technical Conference, v. 2, Samara Research Center, Russian Academy of Sciences, Samara, 2015, 251–255 (In Russian) http://www.ssau.ru/files/science/conferences/pit2015/pit_2015_p2_71.pdf

[30] V. P. Radchenko, Yu. A. Eremin, Reologicheskoe deformirovanie i razrushenie materialov i elementov konstruktsii [Rheological deformation and fracture of materials and structural elements], Mashinostroenie-1, Moscow, 2004, 264 pp. (In Russian)

[31] Rabotnov Yu. N., Polzuchest' elementov konstruktsii [Creep of structural elements], Nauka, Moscow, 1966, 752 pp. (In Russian)