Improvement of the mathematical model for obtaining

S. S. Zakozhurnikov ; G. S. Zakozhurnikova ; T. A. Gorshunova ; O. A. Pikhtilkova ; E. V. Pronina

News of the Kabardin-Balkar scientific center of RAS, Tome 26 (2024) no. 2, pp. 11-25.

Résumé

The main requirements for large industrial enterprises are to increase the energy efficiency of technological processes and improve the environmental friendliness of production. One of the possible solutions to these problems is modeling the main processes occurring in installations and creating an automated control system based on mathematical models. The industrial process for the silicon carbide production is considered. Increase of the process efficiency occurs due to the creation of more advanced operating modes of resistance furnaces based on information obtained during mathematical modeling about the processes that have the greatest impact on melting. Based on the mathematical model, it is possible to build an automated melting process control system, which, based on temperature data at various points in the resistance furnace, will support the most effective silicon carbide melting modes. The mathematical model takes into account the main processes occurring in a resistance furnace during melting, namely: chemical reactions, gas component filtration, the material drying, and energy release attributable to the resistance furnace heater. The technological process mathematical model for the silicon carbide production has been improved. Theoretical foundations for constructing an automated production process control system based on temperature data at the furnace various points were proposed. The current state of the issue of industrial silicon carbide production is presented in the paper. The mathematical model of heat and mass transfer processes in a high-temperature resistance furnace is considered using the example of the technological process of silicon carbide production SiC. The performance of the developed mathematical model was verified by comparing the experiments performed and numerical calculations. The use of an automated control system based on an improved mathematical model is possible at industrial enterprises engaged in the production of fine materials, for example, silicon carbide. The reliability of the results obtained is confirmed by a comparison of experimental data and data obtained using mathematical modeling at the most important points (at the core surface and at the periphery) without taking into account the heating and cooling stages of the resistance furnace. The discrepancy between the data at a point close to the core was a maximum of 15

Détail

Mots-clés : silicon carbide
Keywords: mathematical model, control system

Bibliographie

[1] V. S. Kuzevanov, G. S. Zakozhurnikova, S. S. Zakozhurnikov, “Model of heat and mass transfer in furnaces in the production of silicon carbide”, Alternative energy and ecology, 2015, no. 7 (171), 75–81 (In Russian) | DOI | DOI

[2] A. B. Garyaev, S. S. Zakozhurnikov, V. S. Kuzevanov, “The model of charge precipitation in the production of silicon carbide”, Industrial energy, 2016, no. 9, 27–31, WWCMYR, EDN (In Russian)

[3] V. S. Kuzevanov, A. B. Garyaev, G. S. Zakozhurnikova, “The calculating study of the moisture transfer influence at the temperature field in a porous wet medium with internal heat sources”, Journal of Physics. The calculating study of the: Conference Series, 891 (2017), 012114, Moscow | DOI | MR

[4] L. M. Ozherelkova, E. S. Savin, “Temperature dependence of unsteady thermal conductivity of solids”, Rossiiskii tekhnologicheskii zhurnal, 7:2 (2019), 49–60 (In Russian) | DOI

[5] V. S. Kuzevanov, G. S. Zakozhurnikova, S. S. Zakozhurnikov, “Peculiarities of heat and mass transfer in porous moistened mediums at high thermal loads”, Solid State Phenomena, 299 (2020), 14–19 | DOI

[6] A. A. Mazlov, N. A. Elfimov, G. S. Zakozhurnikova, S. S. Zakozhurnikov, “The effect of filtration transfer on the temperature change in the reaction zone of the resistance furnace for the production of silicon carbide”, [Materials of the International Scientific and Technical Conference «The state and prospects of development of electrical and thermal technology» (XIX Benardos readings), Ivanovo, 2017, 208–210 (In Russian)

[7] V. S. Kuzevanov, S. S. Zakozhurnikov, A. B. Garyaev, “Optimization of the silicon carbide melting process in order to increase its productivity and reduce energy consumption”, Industrial energy, 2015, no. 6, 29–33, UEAGQD, EDN (In Russian)

[8] V. S. Kuzevanov, S. S. Zakozhurnikov, G. S. Zakozhurnikova, A. B. Garyaev, “Process models and calculation of the temperature field in a resistance furnace for the production of silicon carbide”, Bulletin of the Ivanovo State Energy University, 2017, no. 4, 21–29 (In Russian) | DOI

[9] S. S. Zakozhurnikov, Improvement of the silicon carbide production process by changing the organization of heat supply, abstract of the dissertation for the degree of Candidate of technical sciences 05.14.04, Moscow, 2016, 22 pp. (In Russian)

[10] V. S. Kuzevanov, A. B. Garyaev, S. S. Zakozhurnikov, G. S. Zakozhurnikova, “Model of continuous production of fine silicon carbide”, International Workshop «Advanced Technologies in Material Science, Mechanical and Automation Engineering MIP: Engineering - 2019»>, IOP Conference Series: Materials Science and Engineering, Krasnoyarsk, 2019, 32106 | DOI

[11] V. S. Kuzevanov, S. S. Zakozhurnikov, G. S. Zakozhurnikova, A. B. Garyaev, “Finely dispersed silicon carbide synthesis model in the electrothermal reactor with periodic batch loading”, Journal of Physics: Conference Series: 3, Moscow, 022054 | DOI

[12] V. S. Kuzevanov, S. S. Zakozhurnikov, G. S. Zakozhurnikova, “Model and results of a study of the synthesis of finely dispersed silicon carbide in an electro-thermal reactor”, Solid State Phenomena, 316 (2021), 147–152 | DOI

[13] V. S. Kuzevanov, S. S. Zakozhurnikov, G. S. Zakozhurnikova, “Silicon carbide synthesis investigation in an electrothermal fluidized bed”, Journal of Materials Science, 58:43 (2023), 16742–16752 | DOI

[14] K. V. Semeiko, A. I. Malinovsky, A. Zh. Grebenkov et al, “Development of technologies of silicon carbide producing (review)”, NNC RK BULLETIN, 2021, no. 2, 30–41 (In Russian) | DOI

[15] A. S. Polubelova, V. N. Krylov, V. V. Karlin, I. S. Efimova, Abrasive materials production, Mashinostroenie, Leningrad, 1968, 180 pp. (In Russian)

[16] I. S. Katz, “Formation of silicon carbide in an industrial electrical resistance furnace”, Abrasives, 1970, no. 3, 8 (In Russian) | Zbl

[17] S. J. Zinkle, “Fusionmaterials science: overview of challenges and recent progress”, Physics of Plasmas, 12 (2005), 058101 | DOI

[18] T.V. Rozhnova, “Structure and properties of copper powder products for agricultural purposes with silicon carbide made by electrocontact sintering”, Proceedings of the Orenburg State Agricultural University, 2021, no. 4 (90), 178–181 (In Russian)

[19] V. E. Mizonov, V. V. Kostarev, V. A. Zaitzev, “Modeling of moisture transfer in multilayer porous medium at uneven stacking of material layers”, Bulletin of the Ivanovo State Energy University, 2013, no. 4, 76–79 (In Russian)

[20] I. A. Balagurov, V. E. Mizonov, N. Berthiaux, S. Gatumel, “Simulation of mixing kinetics of dissimilar granular materials”, Bulletin of the Ivanovo State Energy University, 2014, no. 6, 67–70, TEJAYX, EDN (In Russian)

[21] R. Sh. Misbakhov, V. E. Mizonov, “Simulation of heat conduction in a composite domain with phase transformation”, Bulletin of the Ivanovo State Energy University, 2015, no. 4, 39–44 (In Russian) | DOI | DOI

[22] A. V. Mitrofanov, N. S. Shpeynova, A. F. Camelo et al., “Experimental and computational study of thermal treatment of particulate fuel in a fluidized bed reactor”, Bulletin of the Ivanovo State Energy University, 2016, no. 1, 58–62 (In Russian) | DOI

[23] Y. E. Bozkurt, U. Emanetoglu et al., “3D printable CNTs and BN hybridized PEEK composites for thermal management applications”, Journal of Materials Science, 58:38 (2023), 1–14 | DOI

[24] D. Reva, M. Lisyatnikov, E. Prusov, Proceedings of MPCPE 2022, Lecture Notes in Civil Engineering, v. 335, 2022 | DOI

[25] Y. Wu, R. Zhao, B. Liang et al., “Construction of C/SiC-Cu3Si-Cu interpenetrating composites for long-duration thermal protection at 2500 C by cooperative active-passive cooling”, Composites Part B: Engineering, 266 (2023) | DOI | Zbl

[26] Ch. Zhao, Z. Tu, J. Mao, “The dynamic thermophysical properties evolution and multi-scale heat transport mechanisms of 2.5D C/SiC composite under high-temperature air oxidation environment”, Composites Part B: Engineering, 263 (2023), 110831 | DOI

[27] K. Feng, Sh. Hu, L. Li et al., “Preparation of low residual silicon content Si-SiC ceramics by binder jetting additive manufacturing and liquid silicon infiltration”, Journal of the European Ceramic Society, 43:13 (2023), 5446–5457 | DOI

[28] Zheng Yi, J. Zou, W. Liu et al., “High pressure sintering of fully dense tantalum carbide ceramics with limited grain growth”, Journal of the European Ceramic Society, 43:12 (2023), 5117–5124 | DOI

[29] S. Zhang, J. Zhang, F. Li et al., “Thermal conductivity of Ca-SiAlON ceramics with varying m and n values”, Journal of the American Ceramic Society, 106:10 (2023), 5642–5647 | DOI

[30] J. Xu, P. Tatarko, L. Chen et al., “High-strength SiC joints fabricated at a low-temperature of 1400 C using a novel low activation filler of Praseodymium”, Journal of the American Ceramic Society, 106:10 (2023), 5679–5688 | DOI

[31] A. Mousavi, V. Vyatkin, “Energy efficient agent function block: A semantic agent approach to IEC 61499 function blocks in energy efficient building automation systems”, Automation in construction, 54 (2015), 127–142 | DOI

[32] V. V. Sleptsov, V. L. Afonin, A. E. Ablaeva, B. Dinh, “Development of an information measuring and control system for a quadrocopter”, Russian technological journal, 2021, no. 9 (6), 26–36 | DOI

[33] S. S. Lavrenov, “Development of an automated sorting system”, Abstracts of reports of the XXIX International Scientific and Technical Conference of Undergraduate and Postgraduate Students «Radio electronics, electrical engineering and power engineering», Moscow, 2023, 152 (In Russian)

[34] S. S. Lavrenov, S. S. Zakozhurnikov, “Application of photovoltaic sensors in production”, A collection of Reports of the International Scientific and Technical Conference «Optical technologies, materials and systems», MIREA Rossijskiy tekhnologicheskiy universitet, Moscow, 2022, 206–209 (In Russian)

[35] A. V. Merkulov, K. Yu. Kharitonova, S. S. Zakozhurnikov et al., “Some issues of creating electronic control systems of rotating objects”, Collection of reports of the Russian Scientific and Technical Conference with international participation «Innovative technologies in electronics and instrumentation», MIREA Rossijskiy tekhnologicheskiy universitet, Moscow, 2021, 212–215 (In Russian)

[36] S. Zakozhurnikov, G. Zakozhurnikova, “Development of a control system for sorting agricultural products according to specified criteria”, E3S Web of Conference, 390 (2023), 03019 | DOI

[37] S. Zakozhurnikov, T. Gorshunova, E. Pronina, O. Raff, “Development of an automated lighting control system in agricultural premises to save energy resources”, IOP Conference Series: Earth and Environmental Science, 1231 (2023), 1–7 | DOI

[38] Y. Tang, L. Li, X. Liu, “State-of-the-art development of complex systems and their simulation methods”, Complex system modeling and simulation, 1:4 (2021), 271–290 | DOI

[39] K. A. Mammadova, E. N. Aliyeva, “Solving the problem of building an automatic control system for the process of water chemical treatment using fuzzy logic”, Lecture Notes in networks and systems, 362 (2022), 748–756 | DOI

[40] L. Zhang, “Electric automation control simulation system based on intelligent technology”, Lecture Notes on data engineering and communications technologies, 125 (2022), 732–738 | DOI

[41] G. S. Renjini, D. Thangavelusamy, “Robust reference tracking and load rejection on non-linear system using controllers”, Gazi University Journal of Science, 35:4 (2022), 1454–1569 | DOI

[42] J. Li, C. Liu, Y. Sun, L. Shao, “A new event-triggered adaptive tracking controller for nonlinear systems with unknown virtual control coefficients”, European journal of control, 69 (2022), 100759 | DOI | MR

[43] A. Dorokhov, A. Aksenov, A. Sibirev, “Results of laboratory studies of the automated sorting system for root and onion crops”, Agronomy, 11:6 (2021), 1257 | DOI

[44] S. Morozov, K. Kuzmin, V. Vershinin, “Development of a simulation automated system for address sorting of correspondence”, Lecture Notes in networks and systems: XIV international scientific conference «INTERAGROMASH 2021», 247 (2022), 927–933

[45] M. G. Tamizi, A. A. Kashani, F. A. Azad, A. Kalhor, “Experimental study on a novel simultaneous control and identification of a 3-DOF delta robot using model reference adaptive control”, European journal of control, 67:5 (2022), 100715 | DOI | MR | Zbl

[46] F. A. Azad, S. Ansari Rad, M. R. Hairi Yazdi et al, “Dynamics analysis, offline-online tuning and identification of base inertia parameters for the 3-DOF Delta parallel robot under insufficient excitations”, Meccanica, 57:2 (2022), 473–506 | DOI | MR | Zbl

[47] S. Zakozhurnikov, O. Pikhtilkova, E. Pronina, O. Raff, “The smart home automated control system development”, AIP Conference Proceedings, 2024, 030024 | DOI