Three-dimensional problem of perfect plasticity (kinematic equations determining three-dimensional plastic flow for a~facet and edge of the Tresca prism)

Yu. N. Radayev

Izvestiya of Saratov University. Mathematics. Mechanics. Informatics, Tome 8 (2008) no. 2, pp. 34-76.

Résumé

In the present study a system of partial differential equations which describes kinematic of three-dimensional plastic flow for the states corresponding to an edge of the Tresca prismis obtained. The system includes the Cauchy equations and the compatibility equations formulated for the displacements and strains increments. These equations are then analysed by the aid of the triorthogonal isostatic co-ordinate net. The systemof kinematic equations is shown correctly determines displacements increments and be of the hyperbolic type. Relations for the displacements increments valid along principal stress lines are derived. Kinematic of plane and axial symmetric plastic flow are separately considered for each case. Kinematic equations for states corresponding to a facet of the Tresca prism which are of the less importance are also examined. Slip kinematic on a surface of maximumshear strain rate in perfectly plastic continuous media is studied. Sliding on the surface is shown can be realized only along asymptotic directions and only within hyperbolic zones of the surface (wherein the Gaussian curvature of the surface is negative). Integrable equations along asymptotic lines of the maximum shear strain rate surface for the jumps of tangent velocities are obtained. Kinematic equations corresponding to elliptic zones on a maximum shear strain rate surface (i.e. if the Gaussian curvature of the surface is positive) are derived and analysed.

Bibliographie

[1] Ivlev D. D., “O sootnosheniyakh, opredelyayuschikh plasticheskoe techenie pri uslovii plastichnosti Treska, i ego obobscheniyakh”, Dokl. AN SSSR, 124:3 (1959), 546–549 ; Ивлев Д. Д., Механика пластических сред, т. I, Теория идеальной пластичности, Физматлит, М., 2001, 15–20 | MR | Zbl

[2] Ivlev D. D., “O vyvode sootnoshenii, opredelyayuschikh plasticheskoe techenie pri uslovii polnoi plastichnosti”, Izv. AN SSSR. OTN. Mekhanika i mashinostroenie, 1959, no. 3, 137 ; Ивлев Д. Д., Механика пластических сред, т. I, Теория идеальной пластичности, Физматлит, М., 2001, 20–21 | MR | Zbl

[3] Radaev Yu. N., Prostranstvennaya zadacha matematicheskoi teorii plastichnosti, Izd-vo Samarsk. gos. un-ta, Samara, 2004, 147 pp.

[4] Nadai A., Plastichnost. Mekhanika plasticheskogo sostoyaniya veschestva, ONTI, M., L., 1936, 280 pp.; Ильюшин А. А., Пластичность. Ч. 1. Упруго-пластические деформации, Гостехтеоретиздат, М., Л., 1948, 376 с.

[5] Tomas T., Plasticheskoe techenie i razrushenie v tverdykh telakh, Mir, M., 1964, 308 pp.

[6] Bykovtsev G. I., Ivlev D. D., Teoriya plastichnosti, Dalnauka, Vladivostok, 1998, 528 pp.

[7] Bykovtsev G. I., Izbrannye problemnye voprosy mekhaniki deformiruemykh sred: Sb. statei, Dalnauka, Vladivostok, 2002, 153 pp.

[8] Malvern L., Introduction to the Mechanics of Continuous Medium, Prentice–Hall, Englewood Cliffs, N.J., 1969, 714 pp.

[9] Washizu K., “A note on the conditions of compatibility”, J. Math. Phys., 36 (1958), 306–312 | MR | Zbl

[10] Moriguti S., “Fundamental theory of dislocations of elastic bodies”, Oyo Sugaku Rikigaku, v. 1, 1947, 87–90

[11] Polozhii G. N., Uravneniya matematicheskoi fiziki, Vyssh. shk., M., 1964, 560 pp.

[12] Mizokhata S., Teoriya uravnenii s chastnymi proizvodnymi, Mir, M., 1977, 259–261

[13] Bers L., Dzhon F., Shekhter M., Uravneniya s chastnymi proizvodnymi, Mir, M., 1966, 58–63 | MR

[14] Kurant R., Uravneniya s chastnymi proizvodnymi, Mir, M., 1964, 239–241 | MR

[15] Petrovskii I. G., Lektsii ob uravneniyakh s chastnymi proizvodnymi, Fizmatgiz, M., 1961., 49–54 | MR

[16] Radaev Yu. N., “Dopolnitelnye teoremy teorii ploskoi i osesimmetrichnoi zadachi matematicheskoi teorii plastichnosti”, Vestn. Samarsk. gos. un-ta. Estestvennonauchnaya ser., 2(32) (2004), 41–61 | MR | Zbl

[17] Sokolovskii V. V., Teoriya plastichnosti, Vyssh. shk., M., 1969, 608 pp.

[18] Bykovtsev G. I., Myasnyankin Yu. M., “O poverkhnostyakh skolzheniya v trekhmernykh zhestkoplasticheskikh telakh”, Dokl. AN SSSR, 167:6 (1966), 1260–1262 | Zbl

[19] Ivlev D. D., Teoriya idealnoi plastichnosti, Nauka, M., 1966, 232 pp. | MR

[20] Bykovtsev G. I., Ivlev D. D., Myasnyankin Yu. M., “O kinematicheskikh sootnosheniyakh na poverkhnostyakh skolzheniya v idealnykh zhestkoplasticheskikh telakh”, Prikl. matem. i mekhanika, 32:4 (1968), 623–631 | Zbl